link to Home Page Logo, Link to Home Page Newman Tools Inc.     Tel 1-800-465-1384     Fax 1-800-605-2442
..."IN STOCK"... vast selection, over 30,000 different items including,
"hard-to-find/special sizes"
        Fast Jump on the Newman Tools' site

30,000 items... In Stock ... hard to find / special sizes ... we ship worldwide, customers in 50 countries

 

High Performance
N-5000 High Purity Anti-Seize


THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.

Data from Oct. 1999




PRODUCT DESCRIPTION
High Performance N-5000 is a specially formulated
nickel based anti-seize lubricant produced under 100%
controlled conditions for highest purity. High Performance N-
5000 is formulated with high purity raw materials and contains
only trace levels of halogens, sulfur, copper, aluminum and
heavy metals, including copper. It provides significant
improvement in anti-seize performance and gives it more
uniform torque tension. High Performance N-5000 has a
general composition of nickel and graphite flake in petroleum
carrier. All ingredients are selected for extreme purity.

Special Features:
· Superior anti-seize: extreme severity anti-seize tests show
stuck studs reduced by 90% compared to products
recommended for the same use
· More uniform torque tension: smaller difference in torque
coeffficients between bolting materials
· High purity: made from highest purity ingredents
· Free from copper: less than 25 ppm copper
· Typically used in applications with a dry surface
temperature of -29 to 1315ºC (-20 to 2400ºF)

TYPICAL APPLICATIONS
· Bolts, studs, valves, pipe fittings, slip fits and press fits in
nuclear electric power generating plants, chemical plants,
pharmaceutical plants, paper mills and other locations
where stainless steel fasteners are used.
Operational Benefits:
· During assembly - prevents high friction, galling and
seizing.
· Promotes uniform and predictable clamping.
· During operation - high purity prevents stress corrosion
· Disassembly - prevents seizing, galling, destruction of
threads

DIRECTIONS FOR USE
· Before or during assembly, wipe brush onto threads and
other joint surfaces needing protection.
· Use full strength. Do not thin.

PROPERTIES OF MATERIAL
Typical Value
Appearance Silver-grey paste
Weight per Gallon, lbs. 9.2 - 10.4
Specific Gravity 1.16 - 1.25
Penetration, ASTM D 217-88 unworked, mm 300 - 390
TYPICAL PERFORMANCE
An anti-seize lubricant used on a bolt helps to develop greater
clamp load for the same torque compared to an unlubricated
bolt. An additional benefit is greater uniformity in clamp load
among a series of bolts. The relationship between torque and
T = K x F x D
· T = Torque (in-lb, ft-lb, N-m)
· K = Torque coefficient or nut factor
· F = Clamp Load (lb, N)
· D = Nominal diameter of bolt (in, ft, m), determined
experimentally.

K Factor:
K factors are obtained on Grade 8, 1/2” steel bolts and Grade 5
nuts by a test procedure which measures torque tension
properties. Lubricant was applied to the bolt threads and both
faces of the washer. See properties chart for the torque
coefficient or K value for the anti-seize compounds. We feel
that this data fairly represents performance to be expected.
However, the manufacturer makes no warranty of specific performance
on any individual fastener. In critical applications, it is
necessary to determine K values independently.
Properties Typical Value
Torque coefficient, k on steel nuts and bolts .15
Type 304 stainless steel .16
Torque coefficient, k (solvent cleaned, not
lubricated) .27

TYPICAL PURITY
Impurities-Combined Test ASTM No. Controlled Typical
& Uncombined Method or (SM16) Max. Value
Chlorine,
Bromine, Iodine
Parr Bomb,
Turbidimetric
D808-87,
C69979
50 ppm 12 ppm
Fluorine Parr Bomb,
Specific ION
Electrode
D3761-84 200 ppm 5 ppm
Sulfur Parr Bomb,
Turbidimetric
D129-64,
D1266-87 100 ppm 9 ppm
Lead Wet Digestion,
AAS
(302D),
D3559-84 25 ppm 1 ppm
Cadmium Wet Digestion,
AAS
(302D),
D3557-84 2 ppm
.2 ppm
Tin Wet Digestion,
AAS
(302D),
E37-76 25 ppm 10 ppm
Zinc Wet Digestion,
AAS
(302D),
D1691-84 25 ppm 1 ppm
Copper Wet Digestion,
AAS
(302D),
D1688-94 50 ppm 2 ppm
Mercury Wet Digestion,
Cold Vapor,
AAS
(302D),
D3223-80 2 ppm .06ppm

GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).

Ordering Information
Part Number Container Size
51572 1 lb. Brush Top Can
Storage
Product shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8°C to 28°C
(46°F to 82°F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container. For further specific shelf life information,
contact your local Technical Service Center.

Data Ranges
The data contained herein may be reported as a typical value
and/or range. Values are based on actual test data and are
verified on a periodic basis.

Note
The data contained herein are furnished for information only and are
believed to be reliable. We cannot assume responsibility for the
results obtained by others over whose methods we have no control. It
is the user's responsibility to determine suitability for the user's
purpose of any production methods mentioned herein and to adopt
such precautions as may be advisable for the protection of property
and of persons
against any hazards that may be involved in the handling and use
thereof. In light of the foregoing, the manufacturer Corporation specifically
disclaims all warranties expressed or implied, including
warranties of merchantability or fitness for a particular purpose,
arising from sale or use of the manufacturer Corporation’s products.
the manufacturer Corporation specifically
disclaims any liability for consequential or incidental damages of
any kind, including lost profits. The discussion herein of various
processes or compositions is not to be interpreted as representation
that they are free from domination of patents owned by others or as a
license under any the manufacturer Corporation patents that may cover such
processes or compositions. We recommend that each prospective
user test his proposed application before repetitive use, using this data
as a guide. This product may be covered by one or more United
States or foreign patents or patent applications.

 

 



Back to Top of Page

horz. bar

 link to product table of contents       link to what's "NEW"        link to price list




Newman Tools Logo




Newman Tools Inc.
185 Iber Road
Stittsville, Ottawa, Ontario, Canada K2S 1E7
Phone: 1-613-836- 6776 or 1-800-465-1384
Fax: 1-613 -836 -9070 or 1-800-605-2442
 
 

Newman Tools Inc.
151 New Park Avenue
Hartford, CT 06106, USA
Phone: 1-800-465-1384
Fax: 1-800-605-2442


Email:     info@newmantools.com

Please send comments, questions, email to   tom@newmantools.com    ( this email will be returned advising you to resend the email to the following email address )

spamfilter1 "at" newmantools "dot" com. This notation is to prevent the robots from harvesting this email address.

return to Newman Tools Home Page.


Go to ... Home Page  | Brand Name index  | Product list  | Technical info  | Price list  | Monthly specials $$$$  | Jokes  | Latest page additions  | Contact Information  | Email the Boss
Servicing the Canadian provinces of Newfoundland, Nova Scotia, New Brunswick, Prince Edward Island, Quebec, Ontario, Manitoba, Saskatchewan, Alberta ,British Columbia and the states of Alabama, Alaska, Arizona, Arkansas, California, Colorado, Connecticut, Delaware, Florida, Georgia, Hawaii, Idaho, Illinois, Indiana, Iowa, Kansas, Kentucky, Louisiana, Maine, Maryland, Massachusetts, Michigan, Minnesota, Mississippi, Missouri, Montana, Nebraska, Nevada, New Hampshire, New Jersey, New Mexico, New York, North Carolina, North Dakota, Ohio, Oklahoma, Oregon, Pennsylvania, Rhode Island, South Carolina, South Dakota, Tennessee, Texas, Utah, Vermont, Virginia, Washington, West Virginia, Wisconsin,Wyoming


February 2003
Newman Tools Inc.